Because it is highly plastic it also has high drying shrinkage. Please exercise caution to dry pieces evenly.
FiringL210 fires to a light brown at cone 02-06. By cone 2 the color intensifies to a dense stoneware brown. Before cone 4 it is over fired. Like any other low-fire body at cone 06-04, L210 is fairly weak and has high porosity. But at cone 02 it is much stronger.
Commercial brush-on glazes are made by many companies, they are typically formulated to fit high-talc bodies (like L213, L212). These bodies have high thermal expansions to reduce the likelihood of crazing. However, when glazes have too high thermal expansion, they can come under excessive compression and shiver off contours or press outward from the inside of ware, cracking it. We cannot guarantee that glazes made by another manufacturer will not craze or shiver. Do stress testing (in boiling water:ice water, the BWIW test). Regarding toxicity: Do not assume food safety of brightly colored glazes in your kiln without a leach test (e.g. GLLE test). Consider using a transparent or white liner glaze for food surfaces.
Many find that commercial brushing and dipping glazes dry very slowly and drip badly. And they often do not fit well (craze or shiver). And they are expensive. With a little effort you can make your own of both types. And add stain and opacifier powders to make almost any color. There is no need to search for a recipe, we have done it for you. You can mix your own glaze from a pre-mixed powder you buy from us or weigh out your own ingredients. However, at low temperature, there is no one-glaze-that-fits-all bodies. To solve this we have created a three-recipe solution, these have thermal expansions that span the entire range of low fire bodies. And they fire crystal clear (in a drop-and-hold firing). Our Zero3 K transparent glaze fits low talc bodies (like L215) and low fire stoneware (like Zero3), Zero3 H fits high talc bodies (like L213, L212) and Zero3 L fits zero talc bodies (like Buffstone). We recommend cone 04-03 using a drop-and-hold firing schedule (for defect free surface and good transparency). Do not trust electronic controllers to be accurate, we verify using cones and manually program to compensate for error. If you need to fire lower or higher than 03, be sure and do testing first.
You can blend the K, H and L glazes to get the best fit. We recommend stress testing by boiling-water-into-ice-water (and vice versa) to bring out any crazing or shivering. If crazing occurs, blend in some of the L. If shivering occurs, blend in some of the H. In this way these glazes can be optimally fitted to almost any clay body.
It is also practical to make your own brushing glazes, ones that will work identically to the commercial ones mentioned above. Like the dipping versions, you can blend to tune the thermal expansion to fit your clay body. You will be surprised at how easy it is and how much money you can save.
Crazing: Functional ware must remain craze-free (crazing is unsanitary and drastically reduces ware strength). Because ware is not crazed out of the kiln does not mean it will not do so with time. Do cycles of a boiling water:ice water immersions (BWIW test) on a piece to test glaze fit (by stressing it to bring out any crazing or shivering tendencies).
Thixotropy: Many people mix their glazes the traditional way, just adding water until the slurry appears to be the right viscosity for dipping. However, if you want better application properties for one-coat dipping, consider creating a thixotropic slurry. Thixotropic glazes are creamy because they have been thinned and then gelled by the addition of a flocculant. They go on evenly, hang on without dripping and dry quickly. Achieving (and maintaining) this state involves targeting a specific gravity (usually around 1.43) and adding epsom salts (1-2g/1000g of powdered glaze).
For slip decoration and engobes be careful to match the fired shrinkage of the slip with the body. Where we do not recommend a specific engobe recipe use a one based on the porcelain itself. Add 2% VeeGum or Bentonite (the extra stickiness helps it adhere well to leather hard ware). Be careful about adding fluxes (e.g. frit), this increases fired shrinkage (the mismatch with body can cause flaking) and can compromise opacity.
We do not supply a thermal expansion value. The reason is that such numbers often mislead users. First, a body has different thermal expansion characteristics when fired at different temperatures, schedules and atmospheres. Dilatometers are only useful when manufacturers can measure bodies and glazes over time and in the same firing conditions. If a chart is supplied here, please view only as a way to compare one body with another.
Another significant issue is that many customers compare measured thermal expansion numbers with calculated values of glazes in efforts to fits those glazes to a body. This does not work. Calculated values are relative only and have limitations that must be understood. The best way to fit glazes to your clay bodies is by testing, evaluation, adjustment and retesting. For example, if a glaze crazes, adjust its recipe to bring the expansion down (using your account at insight-live), fire a glazed piece and thermal stress it (using an IWCT test, 300F into ice-water). If it still crazes, repeat the process.
If we recommend a base clear or glossy glaze, try calculating the expansion of that as a rough guide to know whether your glazes will fit.
Drying Shrinkage: 7.0-8.0% Dry Strength: n/a Water Content: 22.0-23.0% Drying Factor: C130 Dry Density: n/a
Sieve Analysis (Tyler mesh):
+35: tr 35-48: tr 48-65: tr 65-100: 0.5-1.5% 100-150: 2.0-4.0
Cone 06: 10-12% Cone 04: 8.0-10.0% Cone 02: 2.5-3.5 Cone 2: 0.5-1.5
Safety Data SheetClick here for web view.
|Plainsman Clays Ltd.|
702 Wood Street, Medicine Hat, Alberta T1A 1E9
Phone: 403-527-8535 FAX:403-527-7508