G2934 Cone 6 Matte Base Glaze G2926B Cone 6 Clear Glossy Base Glaze GA6-B Alberta Slip Cone 6 Base GR6-A Ravenscrag Cone 6 Base L3954B Mid Temperature Engobe G1916Q Transparent Base Glaze G1947U Transparent Base - Cone 10R G2571A MgO Matte Base - Cone 10R GR10-A Ravenscrag Slip as-a-glaze - Cone 10R L3954N/J Cone 10 Engobe Base
GA6-B Alberta Slip Cone 6 Base
Transparent glaze of choice for dark bodies
The amber color and micro-bubble-free matrix make GA6-B work very well.
Clear glazes often do not work on dark bodies. The center mug is clear-glazed with G2926B (and is full of bubble clouds). This dark body (M390) is exposed inside and out (the other two mugs have the L3954B white engobe inside and midway down the outside). G2926B is an early-melter (starting around cone 02) so it is susceptible to dark-burning bodies that generate more gases of decomposition.
Coffee Clay fired at cone 6 with transparent glazes. The Alberta Slip GA6-B glaze (left) is clearly better that the G2926B on the right. This firing is schedule C6DHSC, a 100F/hr slow cool to 1400F. The glaze is the right certainly has fewer bubbles than normal, but still is not nearly as good as the one on the left.
It is standard practice to fire this at cone 5-6 using a hold and slow cool to produce a defect-free super-gloss surface (we recommend the PLC6DS schedule).
The GA6-A glaze on the insides of these mugs has crystallized during cooling. This happens because of the use of Frit 3134 instead of 3195 and because of the C6DHSC firing schedule (it drops at 150F/hr down to 1400F).
When mixed with water to create a thixotropic slurry, this will perform was as a dipping glaze. It will apply evenly to bisque, produce minimal dripping and dry within seconds. It will be adequately durable for handling. If bisque walls are thin, it will be necessary to glaze the inside and outside of pieces as separate operations (with a drying time between).
If you are glaze layering (using this as a dipping glaze and painting a commercial gummed brushing glaze over it) there is a risk of crawling. It may be necessary to add some gum to this, converting it from a dipping glaze to a base-coat dipping glaze.
This glaze is most often prepared using the traditional method of simply adding water until the desired consistency is achieved (do the initial mix with 85 parts water and 100 powder). We find that 1.45 specific gravity works for us using our tap water. No flocculant additions are generally needed and application properties are very good as long as the slurry is not too viscous or too runny (dries quickly on bisque without cracking and, after dipping, there is minimal dripping).
Left: Raw Alberta Slip powder. Right: Roasted at 1080F. This is a plastic clay, thus it has a significant drying shrinkage. Where a glaze is applied thickly or the percentage of Alberta Slip is high, shrinkage cracks (which produce crawling during firing) will occur. We recommend a mix of roast and raw material in recipes. Roasting the Alberta Slip powder at 1000F greatly reduces the shrinkage. Use a firing rate and hold-time-at-1000F appropriate for the wall thickness and size of your bisque vessels (e.g. 500F/hr and 30 minutes for thin walled small vessels, slower and longer hold for large ones). If any of the powder within is black, increase hold time. Adjust proportions as needed (more roast if the glaze cracks on drying or more raw if it is drying too powdery or not bonding well).
Safety Data SheetClick here for web view.
|Plainsman Clays Ltd.|
702 Wood Street, Medicine Hat, Alberta T1A 1E9
Phone: 403-527-8535 FAX:403-527-7508